Desa CF26PRA User Manual download pdf (Page 20)

www.desatech.com

113897-01C

20

OPERATING FIREPLACE

FOR YOUR SAFETY

READ BEFORE LIGHTING

WARNING: If you do not fol-

low these instructions exactly,

a ﬁre or explosion may result

causing property damage, per-

sonal injury or loss of life.

A. This appliance has a pilot which must be

lighted by hand. When lighting the pilot,

follow these instructions exactly.

B. BEFORE LIGHTING smell all around the

appliance area for gas. Be sure to smell next

to the ﬂoor because some gas is heavier than

air and will settle on the ﬂoor.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electric switch; do not

use any phone in your building.

• Immediately call your gas supplier from

a neighborʼs phone. Follow the gas

supplierʼs instructions.

• If you cannot reach your gas supplier, call

the ﬁre department.

C. Use only your hand to push in or turn the

gas control knob. Never use tools. If the

knob will not push in or turn by hand, donʼt

try to repair it, call a qualiﬁed service tech

-

nician or gas supplier. Force or attempted

repair may result in a ﬁre or explosion.

D. Do not use this appliance if any part has

been under water. Immediately call a

qualiﬁed service technician to inspect the

appliance and to replace any part of the

control system and any gas control which

has been under water.

LIGHTING

INSTRUCTIONS

NOTICE: During initial operation

of new heater, burning logs will

give off a paper-burning smell.

Open a window to vent smell.

This will only last a few hours.

1. STOP! Read the safety information above.

2. Make sure equipment shutoff valve is fully

open.

3. Set switch in OFF position.

WARNING: Burner will come

on automatically within one

minute when the selector switch

is in the ON position after the

pilot is lit.

4. Press in and turn control knob clockwise

to the OFF position.

5. Wait ﬁve (5) minutes to clear out any gas.

Then smell for gas, including near the ﬂoor.

If you smell gas, STOP! Follow “B” in the

safety information, column 1. If you donʼt

smell gas, go to the next step.

6. Press in and turn control knob counter

-

clockwise

to the PILOT position.

Press in control knob for ﬁve (5) seconds

(see Figure 34).

Note: You may be running this heater for

the ﬁrst time after hooking up to gas sup

-

ply. If so, the control knob may need to be

pressed in for 30 seconds or more. This will

allow air to bleed from the gas system.

7. With control knob pressed in, press and

release ignitor button. This will light pilot.

The pilot is attached to the front burner. If

needed, keep pressing ignitor button until

pilot lights.

Note: If pilot does not stay lit, contact a

qualiﬁed service person or gas supplier for

repairs. Until repairs are made, light pilot

with match. To light pilot with match, see

Manual Lighting Procedure, page 21.

8. Keep control knob pressed in for 30 seconds

after lighting pilot. After 30 seconds, release

control knob.

• If control knob does not pop out when

released, contact a qualiﬁed service person

or gas supplier for repairs.

Note: If pilot goes out, repeat steps 4

through 8.

9. Slightly push in and turn control knob coun

-

terclockwise

to the ON position.

Figure 34 - Control Knob and Ignitor

Button Location (Shown as Supplied, No

Control Options)

O

F

F

P

I

L

O

T

L

O

I

H

AUTO

OFF

ON

O

N

Control Knob

Ignitor Button

Selector Switch

Flame

Adjustment Knob

1 2 ... 15 16 17 18 19 20 21 22 23 24 25 ... 35 36

Comments to this Manuals

No comments