Desa CGN10TA User Manual download pdf (Page 11)

104267

OWNER’S MANUAL

Figure 15 - Control Knob In The OFF

Position

LIGHTING

INSTRUCTIONS

1. STOP! Read the safety informa-

tion, page 10.

2. Make sure equipment shutoff valve

is fully open.

3. Turn control knob clock-

wise

Clockwise

to the OFF position.

4. Wait five (5) minutes to clear out

any gas. Then smell for gas, includ-

ing near the floor. If you smell gas,

STOP! Follow “B” in the safety in-

formation on page 10. If you don’t

smell gas, go to the next step.

5. Turn control knob counterclock-

wise

C-clockwise

to the PILOT posi-

tion. Press in control knob for five

(5) seconds (see Figure 15).

Note:

You may be running this

heater for the first time after hook-

ing up to gas supply. If so, the con-

trol knob may need to be pressed

in for 30 seconds. This will allow

air to bleed from the gas system.

6. With control knob pressed in, push

down and release ignitor button.

This will light pilot. The pilot is at-

tached to the front of burner. The

pilot can be seen through the glass

panel. If needed, keep pressing ig-

nitor button until pilot lights.

Note:

If pilot does not stay lit, re-

fer to Troubleshooting, pages 13

through 15. Also contact a qualified

service person or gas supplier for

repairs. Until repairs are made,

light pilot with match. To light pi-

lot with match, see Manual Light-

ing Procedure, column 3.

7. Keep control knob pressed in for

30 seconds after lighting pilot. Af-

ter 30 seconds, release control

knob.

• If control knob does not pop up

when released, contact a quali-

fied service person or gas sup-

plier for repairs.

OPERATING

HEATER

Continued

IGNITOR

PILOT

OFF

Control

Knob

Ignitor

Button

Note:

If pilot goes out, repeat steps

3 through 7. This heater has a safety

interlock system. Wait one (1) minute

before lighting pilot again.

8. Turn control knob counterclockwise

C-clockwise

to desired heating level. The

main burner should light. Set control

knob to any heat level between HI

and LO.

CAUTION: Do not try to ad-

just heating levels by using the

equipment shutoff valve.

Figure 16 - Pilot

Pilot Burner

Ignitor Electrode

Thermocouple

TO TURN OFF GAS TO

APPLIANCE

1. Remove front panel (see Figure 10,

page 8).

2. Follow steps 1 through 5 under Light-

ing Instructions, column 1.

3. With control knob pressed in, strike

match. Hold match to pilot until pi-

lot lights.

4. Keep control knob pressed in for 30

seconds after lighting pilot. After 30

seconds, release control knob. Follow

step 8 under Lighting Instructions,

column 2.

5. Replace front panel.

Shutting Off Heater

1. Turn control knob clockwise

Clockwise

to the OFF position.

2. Turn off all electric power to the ap-

pliance if service is to be performed.

Shutting Off Burner Only (pilot

stays lit)

Turn control knob clockwise

Clockwise

the PILOT position.

THERMOSTAT

CONTROL

OPERATION

The thermostatic control used on these

models differs from standard thermo-

stats. Standard thermostats simply turn

on and off the burner. The thermostat

used on this heater senses the room tem-

perature. The thermostat adjusts the

amount of gas flow to the burner. This

increases or decreases the burner flame

height. At times the room may exceed the

set temperature. If so, the burner will

shut off. The burner will cycle back on

when room temperature drops below the

set temperature. The control knob can be

set to any heat level between HI and LO.

Note:

The thermostat sensing bulb mea-

sures the temperature of air near the

heater cabinet. This may not always agree

with room temperature (depending on

housing construction, installation loca-

tion, room size, open air temperatures,

etc.). Frequent use of your heater will let

you determine your own comfort levels.

MANUAL LIGHTING

PROCEDURE

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 19 20

Comments to this Manuals

No comments

Desa CGN10TA User Manual Page 11

Comments to this Manuals

Related products and manuals for Space heaters Desa CGN10TA