Desa VSGF28NTE User Manual download pdf (Page 10)

www.desatech.com 113135-01A

INSTALLATION

Continued

INSTALLATION CLEARANCES

WARNING: Maintain the

minimum clearances. If you can,

provide greater clearances from

floor, ceiling, and adjoining wall.

Carefully follow the instructions below. This will

ensure safe installation.

Minimum Clearances For Side

Combustible Material, Side Wall, and

Ceiling

A. Clearances from the side of the fireplace cabi-

net to any combustible material and wall

should follow diagram in Figure 8.

Example:

The face of a mantel, bookshelf,

etc. is made of combustible material and pro-

trudes 3

/2" from the wall. This combustible

material must be 4" from the side of the fire-

place opening (see Figure 8).

B. Clearances from the top of the fireplace open-

ing to the ceiling should not be less than 42

inches.

Figure 8 - Minimum Clearance for

Combustible to Wall

*Minimum 16 inches from Side Wall

Example

floor. The corner mantel accessory cannot be in-

stalled with the G3000F/G3001U/G3004W/

G3006F/G3007U hearth base. The corner mantel

can be paired with the G3008F/G3009U/G3010F

corner hearth base. If mounting fireplace and cabi-

net or corner mantel to the floor, an optional G3005

Slim Base kit may be installed.

1. Assemble cabinet mantel, hearth base, and

trim accessories. Assembly instructions are in-

cluded with each accessory.

2. When installing blower, install a properly

grounded, 120 volt three-prong electrical out-

let at fireplace location if an outlet is not there.

If possible, locate outlet so cabinet mantel will

cover it when installed (see Figure 9).

3. Install gas piping to fireplace location. This

installation includes an approved flexible gas

line (if allowed by local codes) after the equip-

ment shutoff valve. The flexible gas line must

be the last item installed on the gas piping.

See Installing Gas Piping to Fireplace Loca-

tion, page 12.

4. Place hearth base accessory against wall at in-

stallation location. Cut an access hole in hearth

top to run gas line to fireplace (see Figure 9).

Make sure to locate access hole so cabinet

mantel will cover it when installed.

Note:

You

can secure base to floor using wood screws.

Countersink screw heads and putty over.

5. Route gas line through access hole in hearth base.

6. Center cabinet mantel on hearth base (see Fig-

ure 10, page 11). Make sure mantel is flush

against wall.

7. Break off nailing flanges (see Figure 11, page

11) with hammer or pliers.

8. Place cardboard or other protective material

on top of hearth base. Carefully set fireplace

on protective material, with back of fireplace

inside mantel opening.

CONVENTIONAL FIREPLACE

INSTALLATION

Conventional installation of this fireplace involves

installing fireplace along with the corner or cabi-

net mantel with hearth base accessories against a

wall in your home (see Accessories, pages 30 and

31). Follow the instructions below to install the

fireplace in this manner.

Note:

The instructions below show installation

using the cabinet mantel and the G3000F/G3001U/

G3004W/G3006F/G3007U series hearth base ac-

cessories. The hearth base accessory shown is

optional for this installation. You can install fire-

place and cabinet/corner mantel directly on the

Figure 9 - Placing Hearth Base

Accessory Against Wall

Electrical

Outlet

Hearth

Base

Rigid Pipe

and Gas

Shutoff Valve

Gas Line

Access

Hole

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 31 32

Comments to this Manuals

No comments

Desa VSGF28NTE User Manual Page 10

Comments to this Manuals

Related products and manuals for Stoves Desa VSGF28NTE