Desa FB-2B User Manual download pdf (Page 7)

7

105563

OWNER’S MANUAL

36"

2"

FLOOR

CEILING

Minimum

Minimum to Top

of Carpeting, Tile,

or Other Combustible

Material

6"

Minimum

From

Sides of

Heater

Left

Side

Right

Side

Figure 4 - Mounting Clearances As Viewed

From Front of Heater

INSTALLATION

For convenience and efficiency, install heater

• where there is easy access for operation,

inspection, and service.

• in coldest part of room.

CAUTION: If you install the

heater in a home garage

• heater pilot and burner must be

at least 18 inches above floor

• locate heater where moving

vehicle will not hit it

IMPORTANT:

Vent-free heaters add mois-

ture to the air. Although this is beneficial,

installing heater in rooms without enough

ventilation air may cause mildew to form

from too much moisture. See Air for Com-

bustion and Ventilation, pages 4 through 6.

CAUTION: This heater cre-

ates warm air currents. These

currents move heat to wall sur-

faces next to heater. Installing

heater next to vinyl or cloth wall

coverings or operating heater

where impurities (such as to-

bacco smoke, aromatic candles,

cleaning fluids, oil or kerosene

lamps, etc.) in the air exist, may

discolor walls.

WARNING: Never install the

heater

• in a bathroom

• in a recreational vehicle

• where curtains, furniture,

clothing, or other flammable

objects are less than 36 inches

from the front, top, or sides of

the heater

• as a fireplace insert

• in high traffic areas

• in windy or drafty areas

WARNING: Maintain the mini-

mum clearances shown in Fig-

ure 4. If you can, provide greater

clearances from floor, ceiling,

and joining wall.

LOCATING HEATER

This heater is designed to be mounted on a

wall.

WARNING: A qualified ser-

vice person must install heater.

Follow all local codes.

CHECK GAS TYPE

Use only propane/LP gas. If your gas supply

is not propane/LP, do not install heater. Call

dealer where you bought heater for proper

type heater.

INSTALLATION ITEMS

Before installing heater, make sure you have

the items listed below.

• piping (check local codes)

• sealant (resistant to propane/LP gas)

• equipment shutoff valve *

• ground joint union

• test gauge connection *

• sediment trap

• tee joint

• pipe wrench

* A CSA/AGA design-certified equipment

shutoff valve with 1/8" NPT tap is an ac-

ceptable alternative to test gauge connec-

tion. Purchase the optional CSA/AGA de-

sign-certified equipment shutoff valve from

your dealer. See Accessory, page 16.

NOTICE: This heater is intended

for use as supplemental heat. Use

this heater along with your pri-

mary heating system. Do not in-

stall this heater as your primary

heat source. If you have a central

heating system, you may run

system’s circulating blower while

using heater. This will help circu-

late the heat throughout the

house. In the event of a power

outage, you can use this heater

as your primary heat source.

Continued

INSTALLING HEATER TO

WALL

Mounting Bracket

The mounting bracket is located on back

panel of heater. It has been taped there for

shipping. Remove mounting bracket from

back panel.

Figure 5 - Mounting Bracket Location

Mounting

Bracket

Removing Front Panel Of Heater

1. Remove two screws near bottom cor-

ners of lower front panel.

2. Pull bottom of lower front panel for-

ward, then down (see Figure 6).

Figure 6 - Removing Front Panel of Heater

1 2 3 4 5 6 7 8 9 10 11 12 ... 19 20

Comments to this Manuals

No comments