Desa FB-2B User Manual download pdf (Page 8)

105563

PROPANE/LP GAS HEATER

INSTALLATION

Continued

Methods For Attaching

Mounting Bracket To Wall

Only use last hole on each end of mounting

bracket to attach bracket to wall. Attach

mounting bracket to wall in one of two ways

1. Attaching to wall stud

2. Attaching to wall anchor

Attaching to wall stud: This method pro-

vides the strongest hold. Insert mounting

screws through mounting bracket and into

wall studs.

Attaching to wall anchor: This method

allows you to attach mounting bracket to

hollow walls (wall areas between studs) or to

solid walls (concrete or masonry).

Decide which method better suits your needs.

Either method will provide a secure hold for

the mounting bracket.

Marking Screw Locations

1. Tape mounting bracket to wall where

heater will be located. Make sure

mounting bracket is level.

Figure 7 - Mounting Bracket Clearances

WARNING: Maintain minimum

clearances shown in Figure 7. If

you can, provide greater clear-

ances from floor and joining wall.

2. Mark screw locations on wall (see

Figure 7).

Note:

Only mark last hole on each end

of mounting bracket. Insert mounting

screws through these holes only.

3. Remove tape and mounting bracket

from wall.

Attaching Mounting Bracket To

Wall

Note:

Wall anchors, mounting screws, and

spacers are in hardware package. The hard-

ware package is provided with heater.

Attaching to Wall Stud Method

For attaching mounting bracket to wall studs

1. Drill holes at marked locations using

9/64" drill bit.

2. Place mounting bracket onto wall. Line

up last hole on each end of bracket with

holes drilled in wall.

3. Insert mounting screws through bracket

and into wall studs.

4. Tighten screws until mounting bracket

is firmly fastened to wall studs.

Attaching to Wall Anchor Method

For attaching mounting bracket to hollow

walls (wall areas between studs) or solid

walls (concrete or masonry).

1. Drill holes at marked locations using

5/16" drill bit. For solid walls (concrete

or masonry), drill at least 1" deep.

2. Fold wall anchor as shown in Figure 8.

3. Insert wall anchor (wings first) into

hole. Tap anchor flush to wall.

4. For thin walls (1/2" or less), insert red

key into wall anchor. Push red key to

“pop” open anchor wings (see Figure

9).

IMPORTANT:

Do not hammer key!

For thick walls (over 1/2" thick) or solid

walls, do not pop open wings.

5. Place mounting bracket onto wall. Line

up last hole on each end of bracket with

wall anchors.

6. Insert mounting screws through bracket

and into wall anchors.

7. Tighten screws until mounting bracket

is firmly fastened to wall.

Figure 9 - Popping Open Anchor Wings

For Thin Walls

Figure 8 - Folding Anchor

Placing Heater On Mounting

Bracket

1. Locate two horizontal slots on back

panel of heater (see Figure 10).

2. Place heater onto mounting bracket.

Slide horizontal slots onto stand-out

tabs on mounting bracket.

Figure 11 - Installing Bottom Mounting

Screws

Figure 10 - Mounting Heater Onto

Mounting Bracket

Installing Bottom Mounting

Screws

1. Locate bottom mounting hole. This

hole is near the bottom on the back

panel of heater (see Figure 11).

2. Mark screw location on wall.

3. Remove heater from mounting bracket.

4. If installing bottom mounting screw

into hollow or solid wall, install wall

anchor. Follow steps 1 through 4 under

Attaching To Wall Anchor Method. If

installing bottom mounting screw into

wall stud, drill hole at marked location

using 9/64" drill bit.

5. Replace heater onto mounting bracket.

6. Place spacer between bottom mount-

ing hole and wall anchor or drilled hole.

7. Hold spacer in place with one hand.

With other hand, insert mounting screw

through bottom mounting hole and

spacer. Place tip of screw in opening

of wall anchor or drilled hole.

8. Tighten screw until heater is firmly se-

cured to wall. Do not over tighten.

Note:

Do not replace front panel at this

time. Replace front panel after making

gas connections and checking for leaks

(see page 10).

Stand-Out

Tab

Mounting Bracket

(attached to wall)

Min.

Adjoining Wall

Only Insert Mounting

Screws Through Last

Hole On Each End

Floor

Horizontal Slots

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 19 20

Comments to this Manuals

No comments

Desa FB-2B User Manual Page 8

Comments to this Manuals

Related products and manuals for Grills Desa FB-2B